- Butt welding fittings
- bends
- T- X- Y- pieces
- T- and Y-bends
- reducers
- caps and heads
- collars
- branch saddles
- orbital fittings
- ANSI / ASME
- Industrial valves
- ball valves
- actuators
- drain cocks
- gate valves
- globe valves
- non-return valves
- Y-strainers
- control technology
- Flanges
- welding neck flanges
- threaded flanges
- blind flanges
- plate flanges
- loose plate flanges
- collars
- flange-fittings
- ANSI/ ASME
- other
- Systems
- TEEKAY
- Victaulic
- press fittings
- quick couplings
- clamp connections
- cutting rings
- DIN 11864/ DIN 11853
- railing construction
- Beverage fittings
- unions
- fittings
- pipe clamps
- Tri-Clamp
- valves & cocks
- flange connections
- inspection glasses
- filter & strainers
- spray balls
Plug fitting -curved elbow 45°SB135
Plug fitting -curved elbow 45° polished surface
>hecoNNECT railing construction system<
Processing
1. Apply adhesive on the part to be glued
2. Turn pipes and fittings in opposite directions and join together
3. Do not handle any more after gluing, allow to harden
The parts can also be fastened with screws or rivets on the underside.
The wall brackets and base plates are fastened using anchors and screws.
You absolutely must make sure that the anchoring requirements are fulfilled!
LOCTITE 638
| Viskosity | Strength | Temp. | max. Game |
| [mPa s] | [N/mm²] | [ °C ] | [mm] |
| 1500-300 | 20 - 35 | -50 bis +150 | 0,25 |
Fast curing, extra strong for dynamically stressed connections.
Final strength after about 12 hours.
Liability:
Due to the large number of different laws and regulations, it is impossible for us to assume
liability for the constructional suitability of our products.
We would therefore like to point out that the ordering party is always responsible for ensuring
the legal regulations are followed.
Before use, clean and degrease the parts and roughen the adhesive areas,
ideal processing temperature is 15° C or higher, apply adhesive sparingly,
and turn both parts in opposite directions.
Do not move for 4 – 5 minutes, hardens after 30 – 60 minutes,
final strength after about 12 hours, do not move during this time.
Remove any glue overflow appearing at the glued areas after hardened,
max. joint of 0.25 mm. Can be separated by heating to over 800°C (blower).
LOCTITE 638 adhesive is used to join and glue cylindrical parts.
The greatest advantage of this adhesive is the simple and rational
production of the parts to be joined – due to the relatively large tolerances.
Permits assembly in the slider seat instead of press and shrink seats,
which are associated with high costs and have the disadvantage of stress concentrations
and warping.
Can be stored for 12 months at max. 20°C.
>hecoNNECT railing construction system<
extended product description
Stainless steel bends welded decoration-bends stick-it curved elbow 45°
Plug fitting -curved elbow 45°SB135
Processing
1. Apply adhesive on the part to be glued
2. Turn pipes and fittings in opposite directions and join together
3. Do not handle any more after gluing, allow to harden
The parts can also be fastened with screws or rivets on the underside.
The wall brackets and base plates are fastened using anchors and screws.
You absolutely must make sure that the anchoring requirements are fulfilled!
LOCTITE 638
| Viskosity | Strength | Temp. | max. Game |
| [mPa s] | [N/mm²] | [ °C ] | [mm] |
| 1500-300 | 20 - 35 | -50 bis +150 | 0,25 |
Fast curing, extra strong for dynamically stressed connections.
Final strength after about 12 hours.
Liability:
Due to the large number of different laws and regulations, it is impossible for us to assume
liability for the constructional suitability of our products.
We would therefore like to point out that the ordering party is always responsible for ensuring
the legal regulations are followed.
Before use, clean and degrease the parts and roughen the adhesive areas,
ideal processing temperature is 15° C or higher, apply adhesive sparingly,
and turn both parts in opposite directions.
Do not move for 4 – 5 minutes, hardens after 30 – 60 minutes,
final strength after about 12 hours, do not move during this time.
Remove any glue overflow appearing at the glued areas after hardened,
max. joint of 0.25 mm. Can be separated by heating to over 800°C (blower).
LOCTITE 638 adhesive is used to join and glue cylindrical parts.
The greatest advantage of this adhesive is the simple and rational
production of the parts to be joined – due to the relatively large tolerances.
Permits assembly in the slider seat instead of press and shrink seats,
which are associated with high costs and have the disadvantage of stress concentrations
and warping.
Can be stored for 12 months at max. 20°C.
This view is not optimized for mobile devices.
You can change back to desktop view.
This view is not optimized for mobile devices.
You can change back to desktop view.