Internet Explorer Warning
Please note: heco gmbh will discontinue support for Internet Explorer in early 2021.
We recommend Microsoft Edge , which is already installed on Windows 10, also Google Chrome or Mozilla Firefox.
deencz
Diesen Artikel aus der Anfrageliste entfernen?
Ja
Nein
Ok
Ok
technical design
Hint
By clicking on this bar you'll return to the table view.
Don't show this hint again!
measures and values
development of stocks
request list
associated articles

Stainless steel ball valves with actuator electric actuators

Electrical rotary actuators

Stainless steel ball valve flanged end with E-actuatorStainless steel blaa valve flanged end

with Electric actuator CH-elec

  • Torque> 300 Nm
  • Protection type IP 67 / IP 68
  • Manual overrride
  • Heater
  • Electric torque limiter




J+J Electric actuators series J4C

 J+J Electric actuators series J4C


An electric actuator serves to automatically open and close a ball valve. The robust polyamide housing, a protection type of up to IP 67 and the two voltage ranges make the electric actuators a simple alternative to a pneumatic actuator. The greatest difference when compared with pneumatic drives are certain to be the shorter switching time, a less frequent switching frequency (standardized pursuant to DIN EN 15714-2) and the polyamide housing. The electric actuators in this series are not EX-protected.


J+J Electric actuators position indicator

  • Manual activation

  • The DOME position indicator clearly displays the current position of the valve

  • A robust plastic housing made of polyamide (protection type IP67)



J+J Electric actuators supply connector

  • Operating lamp – the status LED always indicates the current operating status by means of diverse colours and flashing rates.

  • End position connector – the standard equipment includes two potential-free limit switches

  • Supply connector (a grey DIN cube connector)

  • Emergency operation switch for a manual activation



J+J Electric actuator multi flange

  • Multi flange acc. DIN 3337 / ISO 5211




Service life / Switching cycles

The brushless motor is characterized by the moving rotor and the stationary stator not being connected electrically. This means that the sliding contacts (carbon brushes) that would be subjected to wear as a result of mechanical abrasion and brush arcing, are not required.

This enables the motor to achieve a service life of up to 100,000 switching cycles.



Voltage range

24-240VAC / 24-135VDC

The wide-range power supply self-adaptively recognizes the connected voltage!



Temperature range -20°C / +70°C



Heater

Automatic heating (3.5 W) is a part of the standard equipment.






Accessories

J+J Electric actuators backup battery pack

  • Backup battery pack moves to an intended safety position in the event of there being a power failure



J+J Electric actuators DPS

  • A DPS positioner with a contactless hall effect sensor for analog signals (V/mA). With an input and an output signal or only an output signal.






Ball valve flanged end with E-actuator

Automated ball valves

Stainless steel ball valves with actuator electric actuators

Electrical rotary actuators

Stainless steel ball valve flanged end with E-actuatorStainless steel blaa valve flanged end

with Electric actuator CH-elec

  • Torque> 300 Nm
  • Protection type IP 67 / IP 68
  • Manual overrride
  • Heater
  • Electric torque limiter




J+J Electric actuators series J4C

 J+J Electric actuators series J4C


An electric actuator serves to automatically open and close a ball valve. The robust polyamide housing, a protection type of up to IP 67 and the two voltage ranges make the electric actuators a simple alternative to a pneumatic actuator. The greatest difference when compared with pneumatic drives are certain to be the shorter switching time, a less frequent switching frequency (standardized pursuant to DIN EN 15714-2) and the polyamide housing. The electric actuators in this series are not EX-protected.


J+J Electric actuators position indicator

  • Manual activation

  • The DOME position indicator clearly displays the current position of the valve

  • A robust plastic housing made of polyamide (protection type IP67)



J+J Electric actuators supply connector

  • Operating lamp – the status LED always indicates the current operating status by means of diverse colours and flashing rates.

  • End position connector – the standard equipment includes two potential-free limit switches

  • Supply connector (a grey DIN cube connector)

  • Emergency operation switch for a manual activation



J+J Electric actuator multi flange

  • Multi flange acc. DIN 3337 / ISO 5211




Service life / Switching cycles

The brushless motor is characterized by the moving rotor and the stationary stator not being connected electrically. This means that the sliding contacts (carbon brushes) that would be subjected to wear as a result of mechanical abrasion and brush arcing, are not required.

This enables the motor to achieve a service life of up to 100,000 switching cycles.



Voltage range

24-240VAC / 24-135VDC

The wide-range power supply self-adaptively recognizes the connected voltage!



Temperature range -20°C / +70°C



Heater

Automatic heating (3.5 W) is a part of the standard equipment.






Accessories

J+J Electric actuators backup battery pack

  • Backup battery pack moves to an intended safety position in the event of there being a power failure



J+J Electric actuators DPS

  • A DPS positioner with a contactless hall effect sensor for analog signals (V/mA). With an input and an output signal or only an output signal.






Ball valve flanged end with E-actuator

Automated ball valves